Cookie Img
Back to top
Home » Products » Oil Tank Cleaning Degreaser » Oil Tank Sludge Degreaser

Oil Tank Sludge Degreaser

Oil Tank Sludge Degreaser
Oil Tank Sludge Degreaser
Product Code : OTSD04
Brand Name : JVK UltraClean
Product Description
To describe the standard operating procedure of sludge cleaning using JVK Clean 100, JVK Clean 130, JVK UltraClean.

PRIMARY FUNCTION :

  • JVK Clean 100 is water soluble, biodegreadable degreaser.
  • JVK Clean 130 is water dispersable, oil dispersible nanoemulsion. It works effectively in reducing viscosity, demulsification, and provides superior cleaning efficiency to sticky grease, heavy oil, and solid carbonaceous.
  • JVK UltraClean is nanoemulsioni with capability to reduce interfacial tension, promote water-wet surfaces, and agglomerate long chain paraffin wax and/or asphaltene.

PRODUCT SPECIFICATIONS :


JVK Clean 100

JVK Clean 130

JVK UltraClean

Form

Orange clear liquid

Yellowish Liquid

Drak Borwn Liquid

Specific Gravity

0.98 to 1.05

0.88 to 0.90

0.90 to 0.95

Flash Point (oC)

>80

>65

>40

Biodegradable

Yes

Yes

Yes

Medium

Aqueous

Aqueous/Oil

Aqueous/Oil

Applications for JVK Clean 100

  • Heavy contaminate/ grease/ oil adsorbed on surfaces -
    • Apply neat solution of JVK Clean 100 direct onto the contaminates,
    • Allow it to soak for 20 to 30 minutes
    • Apply sufficient water to remove the contaminate
    • Apply water jet, brush, direct rubbing if necessary
  • Light contaminate/ grease/ oil adsorbed on surfaces
    • Dilute 10% of JVK Clean 100 in water
    • Soak the contaminate surfaces for 30 minutes
    • Apply sufficient water to remove the contaminate
    • Apply water jet, brush, direct rubbing if necessary
  • Enclosure tank, vessel and container cleaning
    • Apply neat of JVK Clean 100, make sure most of the contaminate surfaces in-contact with
    • JVK Clean 100. Suggest to use spray or water jet to apply the JVK Clean 100 direct onto the contaminate surfaces.
    • Apply water into the tank/ vessel/ container until the final concentration of JVK Clean 100 reach 10% of the total volume

Apply the solution to soak for 30 minutes to 2 hours.
Discharge the solution and flush it with sufficient water until no bubbles or foam had been seen.

Cleaning sand particles with JVK Clean 100

  • Prepare solution of JVK Clean 100 with 10% or 20% in water or oil
  • Apply the solution to the contaminate sands
  • Provide sufficient stirring energy to make sure all the sands are able to mix well with the solution for 2 hours

Separation of solids from liquid

Allow the solution to undisturbed until most of the solids settle at the bottom of the vessel. The liquid from the top can be discharge to separator to separate oil from water. The sands or solids are to remove from the bottom. Centrifuge or decanter can be applied subject to specification required. Subject the solution to centrifuge or decanter. The solids may require rinse with water and centrifuge or decant again to meet local specification for disposal

Applications for JVK Clean 130and JVK UltraClean in sludge/ tank cleaning

  • Heavy contaminate/ grease/ oil adsorbed on surfaces -
    • Apply neat solution of JVK Clean 130 direct onto the contaminates,
    • Allow it to soak for 5 to 10 minutes
    • Apply hydrocarbon carrier to remove the contaminate
    • Follow by sufficient water to remove the oily surfaces
    • Apply water jet, brush, direct rubbing if necessary
  • For tank cleaning (to reduce viscosity of sludge oil) and recovery of sludge oil
    • JVK Clean 130 can be diluted with hydrocarbon carrier such as diesel, base oil, crude oil,
    • bunker fuel oil, kerosene, etc in 1% to 5%
    • The solution can be applied to the tank with sludge.
    • Detail of treatment can be discussed together

 


JVK RESOURCES PTE. LTD

Contact Us

( *represents compulsory fields )

Tips on getting accurate quotes. Please include product name, order quantity, usage, special requests if any in your inquiry.